Buffalo Bore Ammunition 38 Special +P 125 Grain Jacketed Hollow Point Box of 20 Information
IMPORTANT INFORMATION ABOUT THE HEADSTAMP ON THIS BRASS: Due to limited supplies of brass, Buffalo Bore has begun loading +P and +P+ ammunition in brass that may not be indicated as such on the headstamp. Example: 9mm Luger +P+ ammunition may be designated as 9mm Luger +P or simply 9mm Luger on the headstamp.
Buffalo Bore loads their ammunition up to maximum SAAMI specifications, which delivers devastating performance on a wide range of game. Please note that this ammunition is not intended for older guns. It is made for modern firearms only, as some of the ammunition could damage older and weaker firearms. This ammunition is new production, non-corrosive, in boxer primed, reloadable brass cases.
Owner of Buffalo Bore Tim Sundles on Buffalo Bore Heavy 38 Special +P Ammunition:
The new Buffalo Bore Heavy 38 SPL+P ammo will maximize the effectiveness of your 38 SPL revolver. The powders are flash suppressed so as to not hinder your vision should you be required to drop the hammer in low light.
Item 20B/20 uses the low velocity (LV) Jacketed Hollow Point bullet that is designed to expand at as little as 800 fps, so you will get expansion out of very short barrels.
Whether you prefer the very soft semi wadcutter lead bullet, or a very soft JHC, (jacketed hollow cavity) these HVY 38 SPL+p loads will turbo charge your 38 SPL revolver.
The tactical reload: Short (2 to 2.5 inch) barreled revolvers have short ejectors. Those short ejectors typically used on 2 inch to 2.5 inch barreled revolvers are not long enough to fully eject 357 magnum brass. So if you are forced into a situation where you need to reload your weapon under fire, you will find yourself picking your fired/empty 357 brass out of the cylinder one at a time – this is very bad. On the other hand, 38SPL brass is shorter than 357 brass and those short ejectors will often fully eject 38SPL brass. We have experimented a great deal with short barreled revolvers and have found that 38SPL brass normally offers an advantage if you need to reload your “snub nose” revolver, in a hurry.
Check out the below velocities that I fired from my personal revolvers. We believe that real world, stock, “over the counter” guns, give real world results, so we don’t advertise velocities that are fired from long test barrels.
These 38SPL+P loads are generating low-end 357 magnum, ballistics. If you have an older or more fragile 38SPL, or if you are recoil sensitive, consider using our HVY Standard Pressure 38SPL ammunition. It is safe to be fired in any 38SPL revolver and it still packs much more punch than ordinary 38SPL ammo.
Item 20B: 125gr. Jacketed Hollow Point. This is the Low velocity version designed to expand under 800 fps. It will mushroom violently and penetrate roughly 12 inches.
- a. S&W mod 60, 2 inch- 1072 fps (319 ft. lbs.)
- b. S&W mod 66, 2.5 inch- 1108 fps (341 ft. lbs.)
- c. Ruger SP101, 3 inch- 1180 fps (386 ft. lbs.)
- d. S&W Mt. Gun, 4 inch- 1258 fps (439 ft. lbs.)
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to – www.P65Warnings.ca.gov.
|Cartridge||38 Special +P|
|Grain Weight||125 Grains|
|Muzzle Velocity||1050 Feet Per Second|
|Muzzle Energy||306 Foot Pounds|
|Bullet Style||Jacketed Hollow Point|
|Shipping Weight||0.650 Pounds|